Cornovo Saddlery logoCORNOVO SADDLERYRequest Quote
Skip to main content

Choose a Saddle Pad by Your Horse’s Back Shape

Key takeaways

  • Fit the back, not just the saddle: wither height, topline shape and symmetry decide the pad profile.
  • High, narrow withers need a contoured spine and clearance; low, broad withers usually suit a straighter pad.
  • Sway backs need built-up centres or shims; roached backs need relief over the spine; straight backs need even thickness.
  • Thickness is no substitute for shape — a thin, well-shaped pad usually outperforms a thick, flat one.
  • Check fit on the bare back before girthing up; ask a fitter or vet about pain, asymmetry or injury.

Two horses can take the same saddle size and need completely different pads. The difference is the back underneath: wither height, the curve of the topline, and whether the left and right sides are symmetrical. This guide shows buyers — tack shops, trainers and distributors — how to read a back and match a pad to it. It describes what to look for; it does not replace a saddle fitter, and where a horse has pain, asymmetry or a recent injury, a fitter or vet should be consulted first. For a shop, the cost of getting this wrong is a return and a lost customer: a pad that does not match the back will slip, bunch or press in the wrong place.

Read the wither first

Stand the horse square and look at the wither from the side. A high, narrow wither needs a pad with a contoured spine and enough clearance that the pad does not press down on the wither under the saddle — check the gap with the saddle in place, and make sure the pad is not pulled down onto the wither when the girth is tightened. A low, broad wither, common in stock-type horses, usually suits a straighter pad with less built-up contour, because a heavily contoured pad can bridge and rock on a flat back. A common mistake is to fix a wither problem with a thicker pad: thickness adds pressure where the saddle already sits close, and can make a fit problem worse. If a customer reports rubbing or soreness at the wither, the shape is usually wrong before the thickness is.

Read the topline: sway, straight or roached

A horse with a dipped or sway back leaves a gap under the middle of the saddle; a pad with a built-up centre, or a shim system, can fill that gap. A straight, level back usually needs a pad of even thickness — adding build-up where none is needed creates pressure points of its own. A roached back, raised along the spine, needs a pad that does not add pressure over the raised area. In each case, the question is not which pad is best but where does this back need support, and where does it need relief? Shims help only when placed where the gap actually is — front, middle or rear. A shim in the wrong place creates a pressure point the horse did not have before, so when a customer is unsure of the shape, a shim-adjustable pad is a safer recommendation than a fixed-shape one.

Check symmetry before you order in bulk

Look at the horse from behind: are the shoulders and hindquarters even? Many horses are slightly asymmetric, and a pad with adjustable shims lets the rider correct a small difference without ordering a custom pad. The correction should be small — shims can even out a modest difference, but they cannot fix a saddle that does not fit or a significant asymmetry, and in those cases a fitter should be involved. For a tack shop, shim systems are worth stocking because one pad plus shims covers more horses than three fixed-shape pads. Note the asymmetry on the customer’s record, so that if the same horse comes back, you already know what worked.

Thickness and material: what they can and cannot do

Wool felt spreads pressure and wicks moisture, which is why it is the standard material for working pads — but thickness is not a substitute for shape. A thin, well-shaped pad usually outperforms a thick, flat one, because shape decides where the pressure goes and thickness only decides how much material sits between saddle and back. As a starting point, match thickness to the job: lighter daily work needs less bulk than long ranch or endurance days. Check with the manufacturer what thickness and density each model is made to, and do not assume two pads labelled the same thickness behave the same — density and construction change how a pad compresses under load. Ask for the specification of the exact model you are ordering, and test a sample before a bulk order: samples are not free, but a sample that confirms the shape is cheaper than a bulk order of the wrong pad.

Discipline changes the answer

A western ranch pad works long hours under a heavy saddle, so durability and moisture handling matter most: the pad must keep its shape and keep wicking through a full working day, not just the first hour. A dressage pad sits under close contact and a precise saddle position, so a stable, non-slip fit matters more than bulk. An endurance pad must handle hours of sweat and movement without bunching or rubbing. The back shape still comes first — but once you know the shape, ask what the horse does all day, and let that decide the material weight and construction. A tack shop that asks both questions sells the right pad the first time. Sheepskin saddle pads are one option where extra cushioning and a soft lining are wanted, but the same rule applies: the back decides the profile, the discipline decides the weight.

A simple fitting check to teach customers

Place the pad on the bare back, then the saddle on top, without girthing up. Look for even contact along the panels, clearance over the wither, and no bridging — daylight under the middle of the saddle. Run a hand under the panels: the pressure should feel even from front to back, with no hard spots and no gaps. Then girth up and walk the horse: the pad should not creep forward or bunch. After a ride, the sweat pattern is a useful second check — even dampness usually means even contact, while a dry patch under a panel can point to a pressure point worth checking with a fitter. Teach this check to your customers and your returns will fall.

What to ask your supplier before you order

Before placing a bulk order with Cornovo Saddlery, confirm the practical points: which profiles are available, contoured and straight, and whether a shim system and spare shims are supplied; the thickness and density each model is made to, in the manufacturer’s own specification; the colour range, since a customer who reorders expects the same colour; and the lead time from order to delivery. The minimum order is 50 pieces per colour, so plan around the profiles and colours that actually sell rather than spreading the order thinly across the whole range. Samples are not free, so order samples of the profiles you are unsure about before the bulk order — a sample on a real horse answers the shape question faster than any specification sheet.

FAQ

Can one pad fit every horse in a barn?

Rarely well. A shim-adjustable pad comes closest, because it adapts to different backs. In a barn with several horses of different shapes, one adjustable pad per horse is still better than one fixed pad shared between them — but a shim system at least lets one model cover more of the barn than a single fixed shape.

Does a thicker pad fix a saddle that rocks?

No — it usually masks the problem and adds pressure. Fix the fit first. A rocking saddle points to a shape mismatch between saddle and back, and a thicker pad only fills the gap temporarily. If the saddle rocks, a fitter should look at it before any pad is recommended.

How do I stock for different back shapes?

Carry contoured and straight profiles, plus a shim option, rather than many thicknesses of one shape. Two profiles and a shim system cover most backs a shop will see, and the stock turns faster than a shelf of one profile in five thicknesses.

Share on facebook
Facebook
Share on twitter
Twitter
Share on linkedin
LinkedIn

Ask For A Quick Quote

We will contact you within 1 working day, please pay attention to the email with the suffix “sales@cornovosaddlery.com”.